Name | Polycaprolactam,glass fiber reinforced |
Synonyms | PERLON NYLON 6 hexanamide POLYAMIDE 6 POLYAMIDE 6 D POLYCAPROLACTAM NYLON 6 POLYCAPROLACTAM Polycaprolactam,glass fiber reinforced |
CAS | 25038-54-4 |
EINECS | 211-024-8 |
InChI | InChI=1/C6H13NO/c1-2-3-4-5-6(7)8/h2-5H2,1H3,(H2,7,8) |
Molecular Formula | [-NH(CH2)5CO-]n |
Molar Mass | 115.174 |
Density | 0.897g/cm3 |
Melting Point | 220 °C |
Boling Point | 255°C at 760 mmHg |
Flash Point | 102.2°C |
Vapor Presure | 0.0167mmHg at 25°C |
Appearance | Crystalline powder |
Storage Condition | Room Temprature |
Refractive Index | 1.433 |
MDL | MFCD00133998 |
Use | For the production of a variety of high-load mechanical parts, electrical and electronic switches and equipment, construction and structural materials, transportation parts; For the manufacture of automotive parts, electrical and electronic equipment and mechanical parts with special requirements for high strength and high temperature resistance; Used for the production of various high load mechanical parts, electrical and electronic switches and equipment, construction and structural materials, transportation parts, etc; A large number of fiber for the textile industry, widely used in the manufacture of mechanical parts, gears, shells, oil-resistant containers, cable sheaths, etc |
Safety Description | S24/25 - Avoid contact with skin and eyes. |
Reference Show more | 1. Hongbo Chen, Mengge Tang, Xiao Yang, Yiu Fai Tsang, Yanxin Wu, Dongbo Wang, Yaoyu Zhou, Polyamide 6 microplastics facilitate methane production during anaerobic digestion of waste activated sludge, Chemical Engineering Journal, Volume 408, 2021, 127251, IS |
Nylon is a kind of engineering plastic with early development and large dosage. It has high impact strength and tensile strength, and excellent abrasion resistance, chemical resistance and solvent resistance. However, due to its great hygroscopicity, the dimensional stability of the product is poor. In addition, although the melting points of nylon -6 and nylon -66 are higher (215 ℃ and 225 ℃ respectively), however, there is a glass transition point around 120 °c, thus allowing a continuous use temperature of only 105 °c. Glass fiber reinforced nylon resin, can overcome the above two shortcomings, the water absorption rate down to 1%, the heat distortion temperature increased to 205 degrees Celsius (reinforced nylon 6) and 250 ℃ (reinforced nylon -66)(both in 1. 86MPa load); Products with good dimensional stability, and further improve the surface hardness, tensile strength, bending strength and wear resistance. 30% glass fiber reinforced nylon 6 and nylon -66, the tensile strength is about 170MPa, the specific strength has been more than the general light metals, such as zinc, magnesium, etc., and aluminum is close. Carbon fiber composite nylon material has the characteristics of small density, high strength, good rigidity, fatigue resistance, creep resistance, antistatic, anti-electromagnetic interference, small coefficient of thermal expansion, good dimensional stability, etc, extrusion molding and other methods of processing.
nylon resin and treated a certain amount of glass fiber or carbon fiber in the ZSK twin screw extruder heat bonding, through the head and die extrusion, cooling shape, traction cut, packaging and storage.
glass fiber reinforced nylon resin is widely used to replace a variety of non-ferrous metals, manufacturing machinery industry in various parts such as gears, transmission parts, etc., and even for large force parts. Nylon reinforced with ultra-fine glass fibers can also be used in the military sector to manufacture satellite components and gun components. Carbon fiber composite nylon materials have a wide range of applications in space equipment, aircraft components, electronic instruments, electronic computers, automobiles, machinery, chemical equipment, sports equipment and so on.
This product is a non-hazardous material, packed with polypropylene woven bag lined with polyethylene film, which can prevent dust and moisture. 25kg net weight per bag. The products should be stored in the warehouse at room temperature, and should not be stacked in the open air. Products must not be exposed to the sun or rain during transportation.
injection, extrusion molding.